Using the remote control
CR-314 Remote Control
Note that greyed-out buttons on the remote control are DVD-
specific and are not used with the CD player.
CD/DVD
Ensure that CD mode is selected using the CD/DVD
toggle button. The ‘CD’ LED above the CD/DVD
button is lit briefly when CD mode is selected.
0–9 keypad
This allows direct access to individual tracks on the disc.
To select a track, press the corresponding keypad button.
For tracks greater than 9, enter the digits in sequence. For
example, to play track 15, press and hold 1 until the number on
the display moves to the left, then press 5.
DISP (display)
Turns the display on or off. Turning the display off generally
produces a slight improvement in sound quality.
CD/DVD REMOTE
CLEAR
CD DVD
If you make a mistake whilst programming you can delete
the last entered track by pressing CLEAR. To delete all
the programmed tracks, press CLEAR repeatedly until ‘0’ is
displayed.
A–B
CD
DVD
1
4
2
5
8
0
3
6
This button enables you to repeat any section of music within
a track. Whilst the disc is playing, press the A–B button at the
start of the section you wish to repeat. ‘REPEAT’ is shown on
the display and the letter ‘A–’ flashes. Press the button a second
time when you reach the end of the section you wish to repeat.
The ‘A–B’ letters stop flashing and remain lit. This section will
To exit the program facility, press PROG.
DISP
A-B
7
9
PROG (Program)
You can program a selection of up to 24 tracks from a
disc to play in any order. Select a track by using the
RPT
CLEAR
PROG
repeat until you press or
or . The forward search button
) moves forward within the selected loop.
(
and
buttons, then press PROG to program the track into
RPT (repeat)
memory (‘PROGRAM’ appears on the display to indicate that you
have started programming a sequence). Repeat these steps to
program the remaining tracks in your selection. Alternatively,
press PROG once and enter your track selection using the 0–9
keypad.
To repeat the entire CD or a pre-programmed selection of tracks
press RPT once: ‘REPEAT’ lights on the display. To repeat a
particular track, select that track and then press RPT twice so
that ‘REPEAT 1’ is shown on the display. If you now select a
different track, that track is repeated instead.
OK
OPEN
The display shows the track numbers programmed, the total
length of the programmed sequence and the number of tracks
programmed (shown by a number below the word ‘STEP’).
To cancel the repeat function press RPT a third time.
Each time you enter a track the number below ‘STEP’ increments
by one and flashes until you press PROG to confirm. If you fail to
press PROG within about five seconds the display stops flashing
and you will have to reselect the track.
Search and Skip Track
Search backwards and forwards;
Skip track backwards and forwards (see page 5)
MUTE
Press to play the program. Press again to replay the entire
sequence from the start. Press and hold CLEAR to erase the
programmed sequence. Press PROG again to exit the program
facility.
OPEN
Opens and closes the CD tray
Playback control
Pause, Play and Stop (see page 5)
MUTE
Stops sound to the speaker outputs of certain Arcam amplifiers.
P MODE
Press once to shuffle play CD tracks (i.e. play them in
a random order). Press again to cancel shuffle play.
P
SUBT
AUDIO
SETUP
TITLE
MEM
MENU
RTN
MODE
Volume +/–
Adjusts the volume on Arcam remote-controllable amplifiers.
ZOOM
Note that the volume (+/–) controls and MUTE button have
no effect on the audio output level of the CD players.
TITLE
Press TITLE once to display the remaining time of the currently
playing track. Press again to display the time remaining of
the disc. Press a third time to turn the text display on.
Press TITLE again and the display reverts to its original setting,
showing the time elapsed for the current track.
ANGLE
STATUS
SRCH
For CDs with text, pressing TITLE once while the disc
is loaded but not playing displays the artist’s name.
Pressing TITLE a second time displays the total number of
tracks and the total playing time.
NOTE: Remember to install the two AAA batteries supplied
before trying to use your remote control.
CR-314
Do not place anything in front of the display area on the
CD player (where the IR receiver is located), or the remote
control may not work.
CD93
6
