owner’s manual
SCT-560
HIGH-SPEED DUBBING STEREO CASSETTE DECK
IMPORTANT SAFETY INSTRUCTIONS
Careful attention is devoted to quality standards in the manufacture of your cassette deck, and safety is a
major factor in its design. However, safety is also your responsibility.
The SCT-560 is made and tested to meet
exacting safety standards. It meets both
UL and FCC requirements
This section lists important information that will help you properly use and enjoy your cassette deck and
accessories. Read all the included safety and operating instructions before using your cassette deck, follow
them closely, and retain them for future reference.
Heed Warnings — Follow all warnings on the product and in the operating instructions.
To prevent fire or shock hazard, do not
expose this system to rain or moisture.
Cleaning — Unplug this product from the wall outlet before cleaning. Use only a damp cloth for cleaning.
Do not use liquid or aerosol cleaners.
Attachments — Do not use attachments/accessories not recommended by the product manufacturer, as
they might create a hazard.
Water and Moisture — Do not use this product near water (for example, near a bathtub, washbowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool).
CAUTION
Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.
Follow the manufacturer’s instructions for mounting, and use a recommended mounting accessory.
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL.
Carts — Move the product on a cart carefully. Quick stops, excessive force, and
uneven surfaces may cause the product/cart to overturn.
Ventilation — Slots and openings in the cabinet provide ventilation, ensure
reliable operation, and protect from overheating. Do not block or cover these
openings, and do not place the product on a bed, sofa, rug, or other similar
surface. Do not place the product in a built-in bookcase or rack unless it provides
proper ventilation as specified by the manufacturer.
Power Sources — Operate this product using only the power source indicated on its marking label. If
you are not sure of your home’s power type, consult your product dealer or local power company.
Polarization — This product is equipped with a polarized AC line plug (a plug having one blade wider
than the other). This plug will fit in the power outlet only one way. This is a safety feature. If you cannot
insert the plug fully into the outlet, try reversing the plug. If the plug still doesn’t fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If you
need an extension, use a polarized cord.
This sym bol is intended to
alert you to the presence of
u n in s u la te d
d a n g e ro u s
Power-Cord Protection — Route power-supply cords so they are not likely to be walked on or pinched
by items placed on or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
voltage within the system ’s
enclosure that m ight be of
s u fficie n t m a g n itu d e to
constitute a risk of electric
s h o ck. Do n o t o p e n th e
system ’s case.
Lightning — For added protection for this product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and power-line surges.
Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles, as this
can result in a risk of fire or electric shock.
Objects and Liquids — Never push objects of any kind into this product through openings, as they may
touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
This sym bol is intended to
inform you that im portant
operating and m aintenance
instructions are included in
the literature accom panying
this system .
Servicing — Do not attempt to service this product yourself, as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
•
•
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled or objects have fallen into the product.
If the product has been exposed to rain or water.
This equipment complies with the limits for a Class B digital
device as specified in Part 15 of FCC Rules. These limits
provide reasonable protection against radio and TV
interference in a residential area. However, your equipment
might cause TV or radio interference even when it is
operating properly. To eliminate interference, you can try
one or more of the following corrective measures:
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
•
•
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance.
•
•
Reorient or relocate the receiving antenna.
Replacement Parts — When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or having the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
Increase the distance between the equipment and
the radio or TV.
•
Use outlets on different electrical circuits for the
equipment and the radio or TV.
Safety Check — Upon completion of service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Consult your local Radio Shack store or an experienced
radio/TV technician if the problem still exists.You must use
shielded interface cables with this equipment.
Wall or Ceiling Mount — The product should be mounted to a wall or ceiling only as recommended by
the manufacturer.
Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
3
CONTENTS
Connections ............................................................................................................................. 5
Connecting to Your Receiver/Amplifier ....................................................................................................... 5
Connecting the Remote Control Cable ........................................................................................................ 5
Connecting the CD-Deck Synchro Control Cable........................................................................................ 5
Connecting Power ....................................................................................................................................... 5
Basic Operation ........................................................................................................................ 6
Loading and Playing a Cassette Tape.......................................................................................................... 6
Loading a Cassette Tape ........................................................................................................................ 6
Playing a Cassette Tape ......................................................................................................................... 6
Dolby Noise Reduction (NR) ....................................................................................................................... 7
Setting DOLBY NR for Playback ............................................................................................................ 7
Setting DOLBY NR for Recording........................................................................................................... 7
Recording with the Dolby HX Pro System .............................................................................................. 7
Special Features ....................................................................................................................... 8
Fast-Forward/Rewind ................................................................................................................................. 8
Pause ........................................................................................................................................................... 8
Blank Skip .................................................................................................................................................. 8
Tape Counter .............................................................................................................................................. 8
Automatic Search Music System ................................................................................................................. 8
Using Relay Play ......................................................................................................................................... 9
Playback Sequence................................................................................................................................. 9
Rewind Auto Play........................................................................................................................................ 9
Demo Mode ................................................................................................................................................. 9
Recording and Dubbing ............................................................................................................................ 10
Recording from Line-In Sources ........................................................................................................... 10
Recording Blank Spaces Between Selections ........................................................................................ 11
Copying a Cassette Tape (Dubbing) .................................................................................................... 11
CD-Deck Synchro Recording ................................................................................................................ 12
Tape Hints .............................................................................................................................. 13
Restoring Tape Tension and Sound Quality .............................................................................................. 13
Erasing a Cassette Tape ............................................................................................................................ 13
Erase-Protection Tabs ............................................................................................................................... 13
Care and Maintenance ........................................................................................................... 14
Cleaning the Tape-Handling Parts ............................................................................................................ 14
Troubleshooting ..................................................................................................................... 15
Specifications ......................................................................................................................... 17
Index to Features by Control Name ....................................................................................... 18
Notes ...................................................................................................................................... 19
4
CONNECTIONS
TAPE/ DCC
REC
PLAY
TAPE
2
INPUT
CD
__
L
VCR/
LD
PHONO
PLAY
REC
LINE
OUTPUT
PLAY
L
R
L
L
INPUT
REC
CONTROL
CONTROL
L
R
OUT
CD¥DECK
SYNCHRO
IN
R
R
R
OUT
L
L
R
R
L
R
R
L
Receiver/Amplifier
SCT-560
LINE OUT
CD• DECK
SYNCHRO
CONTROL
L
R
IN
OUT
CD Player
CONNECTING TO YOUR RECEIVER/AMPLIFIER
1. Using one of the supplied audio cables, connect the
cassette deck’s L and R LINE OUTPUT jacks to the
receiver/amplifier’s left and right tape input jacks.
CONNECTING THE CD-DECK SYNCHRO
CONTROL CABLE
If you have a CD player that has a CD-DECK SYNCHRO
control jack, connect the jack to your cassette deck’s CD-
DECK SYNCHRO control jack using the supplied CD-
deck synchro control cable. This connection lets you
easily make CD-to-cassette deck recordings. See “CD-Deck
Synchro Recording” on Page 12.
2. Using the other audio cable, connect the cassette deck’s
LINE INPUT jacks to the receiver/amplifier’s tape
output jacks.
Note: If you are not sure which receiver/amplifier jacks to
use, refer to your receiver/amplifier’s owner’s manual.
CONNECTING POWER
Carefully check all connections. Then plug the AC power
cord into a standard AC outlet. The power cord’s plug is
polarized and fits only one way. The cassette deck
automatically turns on.
CONNECTING THE REMOTE CONTROL CABLE
If you have an RCA receiver/amplifier that has a remote
control jack (labeled CONTROL IN/OUT), you can use the
receiver/amplifier’s remote control to operate the cassette
deck.
Warning: To prevent electric shock, do not plug the
power cord into an extension cord or other receptacle
unless you can fully and easily insert the plug’s blades.
Connect the receiver/amplifier’s CONTROL OUT jack to
the cassette deck’s CONTROL IN jack using the supplied
remote control cable.
If you have another RCA audio component that has a
remote control jack, connect the cassette deck’s
CONTROL OUT jack to the component’s CONTROL IN
jack. This relays the remote control signal from the
receiver/amplifier to the other component.
5
BASIC OPERATION
LOADING AND PLAYING A CASSETTE TAPE
Loading a Cassette Tape
1. Use your finger or a pencil to turn the
cassette’shub and take up any tape slack.
Note: Avoid touching the tape. Fingerprints attract dirt.
8. Press STOP (7) to stop playback.
9. Press EJECT (0) to open the cassette door
and remove the cassette.
10. To turn off the cassette deck, press POWER.
Only the STAND BY indicator lights.
2. Press the appropriate EJECT (0) button
(Deck1 or Deck 2) to open the cassette
compartment door.
3. Load the cassette with its open edge down.
Since the decks play in either direction, it does
not matter which side faces out.
4. Gently close the compartment door.
Playing a Cassette Tape
1. Turn on the cassette deck by pressing POWER.
2. Load a tape.
3. Set DOLBY NR to the setting used when the
tape was recorded. See “Dolby Noise
Reduction.”
4. Set REV MODE for one-side, two-side, or
continuous two-side play.
“
The cassette deck plays or records one side of the
tape and stops.
[
The cassette deck plays or records both sides of
the tape and stops.
Note: To play or record both sides, you must press 3 (not 2).
” The cassette deck plays the tape up to eight times
(16 sides) and stops.
Note: During recording, this setting is the same as one-
side play.See “Using Relay Play” for more details about
REV MODE.
5. Set the receiver/amplifier’s volume to its lowest
position.
6. Press 3 on the appropriate deck to play the
side facing you. Press to play the side facing
away from you.
7. Adjust the receiver/amplifier’s volume, tone,
and balance.
6
BASIC OPERATION
DOLBY NOISE REDUCTION (NR)
Dolby NR systems reduce tape hiss and background noise.
When recording, the systems listen for places where you
might later hear hiss. The systems record these sections at
a higher level. When you play the tape, the systems
decrease these sections’ volume, restoring the music to its
original level and reducing the noise level.
Dolby B NR reduces background noise by about 10 dB.
Dolby C NR reduces background noise by about 20 dB.
Setting DOLBY NR for Playback
When you play a cassette tape, set DOLBY NR for the
system used when the tape was recorded. For prerecorded
tapes, use these guidelines to set DOLBY NR:
•
•
•
If Dolby NR or 2 is not on the cassette label,
set the switch to OFF.
If Dolby NR or 2 does appear, but the label does
not specify Dolby C NR, set the switch to B.
If Dolby C NR is on the label, set the switch to C.
Setting DOLBY NR for Recording
Set DOLBY NR for the system you want to use.
You can play cassette tapes recorded with Dolby B or C
NR on players that do not have the same system.
However, high-frequency sounds might be too loud —
especially in Dolby C NR recordings.
Recording with the Dolby HX Pro System
If the source you are recording has many high-frequency
signals, the signals can reduce the overall recording
quality. During recording, the Dolby HX Pro system
adjusts for these signals to improve high-frequency
response. This feature is always turned on during
recording.
You can play a cassette tape recorded with the Dolby HX
Pro system on any cassette player.
7
SPECIAL FEATURES
•
To skip to the beginning of the next (or a
later) selection:
FAST-FORWARD/REWIND
To rapidly advance or rewind the tape, press ¡ or 1.
To stop the tape, press STOP (7). When the tape reaches
the end, the cassette deck automatically stops.
Press ¡ or 1 — whichever points in the same
direction as the 3 or 2 indicator.
PAUSE
Note: If you press (¡ or 1) more times than the
number of selections on the side you want to search,
and have not set REV MODE to “ , the search
continues to the other side.
To temporarily stop Deck 2 during playback or recording,
press PAUSE (8). To restart, press 8, 3, or 2.
Note: You cannot pause while fast-forwarding or rewinding.
ASMS might not operate as expected if:
BLANK SKIP
•
•
•
The pause between selections is less than 4 seconds
long.
To have the cassette deck automatically fast-forward
through blank spaces on the tape, set REV MODE to
RELAY/SKIP. If the cassette deck encounters 15 seconds
of silence, it fast-forwards to the end of the blank section
and resumes normal play from that point. If the tape
reaches the end, it reverses and plays the other side.
The overall recorded volume level of a selection is
very low.
The noise level between selections is very high.
TAPE COUNTER
As you play or record a tape, the tape counter advances
for the tape side facing you or decreases for the tape side
facing away from you. At the beginning of a tape or
selection, press RESET to reset the counter to 0000. You
can then use the tape counter to quickly locate a specific
section on the tape.
The deck can also show the elapsed playing time (in
minutes and seconds) since you reset the time. To switch
between displays, press TIME/COUNTER on the deck you
are using. (The time does not advance when you fast-
forward or rewind the tape.)
AUTOMATIC SEARCH MUSIC SYSTEM
The automatic search music system (ASMS) lets you
quickly locate a desired selection on a cassette tape. It
searches for the blank space before a selection and
automatically stops just before playback begins.
ASMS operates only during play. If the cassette deck is
stopped, first press 3 or 2.
•
To skip to the beginning of the current (or an
earlier) selection:
Press ¡ or 1 — whichever points in the
opposite direction of the or indicator.
To skip to the beginning of an earlier selection,
repeatedly press the button.
8
SPECIAL FEATURES
USING RELAY PLAY
You can load two cassette tapes to play one after the other.
REWIND AUTO PLAY
To have Deck 1 rewind the cassette to the beginning of the
current side and start play, press REWIND AUTO PLAY.
Notes:
Note: If both decks have tapes loaded, the decks operate
as described under “Using Relay Play.”
•
The cassettes you load should have the same
Dolby NR type.
•
•
You can start relay play from either Deck 1 or Deck 2.
You can replace the tape in the idle deck during
relay play.
DEMO MODE
The cassette deck has a demonstration mode that
alternately turns on various indicators and meters so you
can see where they show on the deck.
•
When a tape automatically begins playing during
relay play, it always starts from the forward (3)
playback side. Be sure to set the tapes properly
before starting relay play.
To turn on the demonstration mode, press TIME/COUNTER
and RESET on Deck 2 at the same time while the cassette
deck is stopped. To cancel the mode, press any button
except EJECT(0) and POWER.
•
If the deck encounters an unrecorded portion of
tape more than 15 seconds long, it fast forwards
the tape until it finds another recorded portion,
and resumes playback from that point (i.e., blank
skip is automatically set).
1. Load a cassette tape in each tape
compartment, then close the compartment
doors.
2. Set DOLBY NR for the noise-reduction system
you want to use. See “Dolby Noise Reduction”
on Page 7.
3. Set REV MODE to RELAY/SKIP.
4. Press or on Deck 1 or 2. Playback starts. See
“Playback Sequence.”
5. Adjust the volume, tone, and balance control
on your receiver/amplifier for the desired
sound.
6. To stop relay play before it automatically stops,
press STOP(7) on the deck that is playing
any time during playback.
Playback Sequence
The cassette deck repeats the following sequence 8 times
(up to 32 sides).
Where playback starts in the sequence depends on which
play button you press first:
I. Side facing out, Deck 1
II. Side facing in, Deck 1
III. Side facing out, Deck 2
IV. Side facing in, Deck 2
•
•
•
•
When you press 3 on Deck 1, playback starts at I.
When you press 2 on Deck 1, playback starts at II.
When you press 3 on Deck 2, playback starts at III.
When you press 2 on Deck 2, playback starts at IV.
9
SPECIAL FEATURES
RECORDING AND DUBBING
You can record from any component connected to the
receiver/amplifier or dub (copy) cassette tapes.
Notes:
•
•
Tape quality greatly affects the quality of the
recording. Your cassette deck can play Type I, Type
II, and Type IV tape. We recommend Radio Shack
brand tapes.
Before recording or dubbing, be sure the cassettes
onto which you want to record or dub have their
erase-protection tabs in place. To prevent
accidental erasure of a tape, remove the erase-
protection tabs. For more information, see “Erase-
Protection Tabs.”
•
To record at the beginning of a cassette, turn the
cassette’s hub with your finger or a pencil until the
dark part of the tape enters the opening in the
edge of the cassette. Before dubbing, position both
tapes this way to prevent missing recording
material at the very beginning of a tape.
Recording from Line-In Sources
To record from the device connected to the cassette deck’s
LINE INPUT jacks, follow these steps.
1. Press POWER to turn on the cassette deck.
2. Load a blank tape (or one you want to record
over) into Deck 2. Be sure the side you want
to record on is facing you and the full reel is
to the left.
3. Press 3 on Deck 2 to set the tape direction
and then press 7 .
4. Set DOLBY NR for the noise-reduction system
you want to use. See “Dolby Noise Reduction”
on Page 7.
5. Set REV MODE. See “Loading and Playing a
Cassette Tape.”
6. Press RECORD(¶). The cassette deck enters
the record pause mode.
7. Play the loudest part of the selection you want
to record.
Set REC LEVEL so the LEVEL meter goes to -3 dB
most of the time and to 0 dB at peaks. This gives the
recording a high signal-to-noise ratio with minimum
distortion.
8. Start the source you want to record, then press
3 on Deck 2 to begin recording.
9. To stop recording, press 7 on Deck 2.
10
SPECIAL FEATURES
Recording Blank Spaces Between
Selections
7. To begin dubbing, press the appropriate COPY
button:
Some cassette decks search for the blank spaces between
selections so you can quickly locate specific selections. If
the original program does not have blank spaces, you can
add them when you make a new recording.
NORMAL to dub at normal playback speed.
HI-SPEED to dub at twice the normal speed.
The cassette in Deck 1 automatically plays.
Both decks automatically stops when either tape reaches
the end.To manually stop dubbing, press 7 on either
deck; this stops both cassette decks.
While the cassette deck is set to record or record pause,
press REC MUTE(•).The deck records 41/2 seconds of
silence and pauses. To begin recording again, press
PAUSE(8) or the appropriate play button (3 or 2).
•
To record a blank space of more than 41/2 seconds,
press again after the cassette deck pauses, or press
and hold for the desired length of time. To begin
recording again, press 8, 3, or 2.
•
To record a blank space of less than 41/2 seconds,
press before 41/2 seconds pass. To begin recording
again, press 8, 3, or 2.
Copying a Cassette Tape (Dubbing)
Notes:
•
If the original recording has Dolby B NR or Dolby
C NR, the copy will also have it, regardless of the
position of DOLBY NR. If the original does not
have Dolby NR, you cannot add it to the tape you
are dubbing.
•
•
REC LEVEL does not affect the recording level
during dubbing.
Both decks automatically stops when either tape
reaches the end. We recommend you dub onto a
tape that is the same length as the original, so the
decks stop at the same time.
To copy a cassette tape:
1. Press POWER to turn on the cassette deck.
2. Load the cassette tape you want to copy into
Deck 1. Be sure the side you want to copy
faces you with the full reel to the left.
3. Load a blank tape (or one you want to record
over) into Deck 2. Be sure the side you want
to record on is facing you and the full reel is
to the left.
4. Set REV MODE. See “Loading and Playing a
Cassette Tape.”
5. Press 3 on Deck 1 to set the tape direction,
then press 7.
6. Press 3 on Deck 2 to set the tape direction,
then press 7.
11
SPECIAL FEATURES
If REV MODE is set to automatically switch to the
other side of the tape and the tape reaches the end of
the first side while the CD player is playing, the CD
player returns to the beginning of the current track and
pauses. A 41/2-second blank space is automatically created
on the reverse side of the tape, then the CD player
resumes playback and the deck resumes recording.
CD-Deck Synchro Recording
If your CD player has a compatible CD Synchro function,
you can automatically record your CDs. Connect the CD
player’s and cassette deck’s CD SYNCHRO jacks as
described in “Connecting the CD-Deck Synchro Control
Cable.”
Note: A 41/2-second blank space is automatically created
between selections.
1. Load a compact disc in the CD player.
2. Load a blank tape (or one you want to record
over) into Deck 2. Be sure the side you want
to record on is facing you and the full reel is
to the left.
3. Press on Deck 2 to set the tape direction and
then press .
4. Set REV MODE and DOLBY NR.
5. Press RECORD.
6. Select the CD player on the receiver/amplifier,
then begin play on the CD player.
7. Adjust the recording level.
8. Press the stop buttons on the cassette deck
and the CD player.
9. Press CD SYNCHRO RECORD. Recording
automatically begins.
When the compact disc finishes playing, the CD
player stops and the cassette deck pauses. Within 1
minute, change the disc and start play on the CD player to
resume recording. If the CD player does not start play
within 1 minute, the cassette deck stops.
When the CD player changes discs (multi-disc CD players),
the cassette deck pauses, then resumes recording when
the CD player begins playing the next disc.
If the cassette deck reaches the end of the tape and
stops while the CD plays, the CD player returns to the
start of the current track, then pauses. To resume
recording, load another tape and ensure the tape is
moving in the desired direction. If it is not, press a play
button ( 3 or 2 ) on the cassette deck to change the tape
direction, then immediately press 7. You can resume
recording by pressing CD SYNCHRO RECORD again.
(Press the button within 1 minute after the CD player
pauses. If more than 1 minute elapses, the CD player
stops.)
12
TAPE HINTS
If you later decide to erase or record over the tape, you
can place a piece of tape over the holes.
RESTORING TAPE TENSION AND SOUND
QUALITY
After you play a cassette tape several times, the tape might
become tightly wound on the reels. This can cause
playback sound quality to deteriorate.
To restore the sound quality, fast-forward the tape from
the beginning to the end of one side, then completely
rewind it. Then loosen the tape reels by gently tapping
each side of the cassette’s outer shell on a flat surface.
Note: Be careful not to damage the cassette when tapping
it. Do not touch the exposed tape or allow any sharp
objects near the cassette.
Note: When covering the holes, cover only the place that
was originally protected by the plastic tab.
ERASING A CASSETTE TAPE
If you no longer want a recording, you can record over it
or erase it.
To record over a cassette tape, simply record as usual. The
cassette deck records over the previous recording.
To erase a cassette tape, turn off the input source and set
REC LEVEL to MIN and press RECORD (¶).
Then press 3 or 2 to begin recording. To erase the entire
cassette tape, let the tape record to the end of both sides.
You can quickly erase both sides of a cassette tape using a
bulk tape eraser, available at your local Radio Shack store.
ERASE-PROTECTION TABS
Most cassette tapes have two erase-protection tabs — one
for each side of the tape. When a tab is in place, you can
erase or record on that tape side.
To protect your recordings from being accidentally erased
or recorded over, carefully break off the erase-protection
tabs, using a screwdriver or similar tool.
Side A Tab
Note: Breaking off the tabs does not prevent a bulk tape
eraser from erasing the tape.
13
CARE AND MAINTENANCE
Your RCA SCT-560 High-Speed Dubbing Stereo Cassette
Deck is an example of superior design and craftsmanship.
These suggestions will help you care for the cassette deck
so you can enjoy it for years.
Capstan
Capstan
Pinch Roller
Keep the cassette deck dry. If it gets wet, wipe it
dry immediately. Liquids can contain minerals
that can corrode the electronic circuits.
Pinch Roller
Recording/Playback Head
Handle the cassette deck gently and carefully.
Dropping it can damage the circuit boards and
case and can cause the cassette deck to work
improperly.
DECK 2
Note: RadioShack stores sell a wide variety of tape deck
cleaning supplies.
Use and store the cassette deck only in normal
temperature environments. Temperature
extremes can shorten the life of electronic
devices and distort or melt plastic parts.
Keep the cassette deck away from dust and dirt,
which can cause premature wear of parts.
Wipe the cassette deck with a damp cloth
occasionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or strong
detergents to clean the cassette deck.
Modifying or tampering with the cassette deck’s internal
parts can cause a malfunction and might invalidate your
cassette deck’s warranty and void your FCC authorization
to operate it. If your cassette deck is not operating as it
should, take it to your local Radio Shack store for
assistance.
Cleaning the Tape-Handling Parts
Clean the tape-handling parts after about every 20 hours
of use. Use a cotton swab dipped in tape head cleaning
solution or denatured alcohol to gently clean the parts
shown in the illustration.
Capstan
Capstan
Pinch Roller
Pinch Roller
Playback Head
14
DECK 1
TROUBLE SHOOTING
This cassette deck has been manufactured to the specifications of RadioShack and is covered by a limited warranty from
RadioShack. If your cassette deck is not operating as it should, take it to your local RadioShack store or call 1-800-THE-
SHACK for assistance.
Your cassette deck should give you years of trouble-free service if you follow the instructions in this manual. If you do have
problems, the chart below can help you solve them. If you still have problems after following the suggestions below, take the
cassette deck to your local Radio Shack store for assistance.
Symptom
Remedy
Cause
Power does not come on.
• Plug in the power cord.
• Turn on the component.
• The power cord is unplugged.
• The component to which the power
cord is attached is turned off.
The door does not open.
The door does not close.
The tape immediately stops.
• Press 7.
• The deck is not stopped.
• Remove and reinsert the cassette.
• The cassette is not properly loaded.
• The tape is at the end of that side.
• The tape has too much slack.
• Play the other side of the tape or rewind
the tape.
• Take up the slack.
The level meter does not work
during playback.
• Replace the tape with one that has a
recording.
• There is nothing recorded on the
tape.
• Clean the tape heads.
• The tape heads are dirty.
There is no sound.
• Set the receiver/amplifier’s input selector
to the same input you connected the
deck to.
• The receiver/amplifier’s input selector
is not properly set.
• Turn up the receiver/amplifier’s volume.
• Check all connections.
•
The receiver/amplifier’s volume is too low.
• There are connection problems.
The record indicator does not
light when you try to record.
• Replace the tape with one with unbroken
tabs or cover the holes with tape.
• The erase protection tabs are broken
off.
The level meter does not work
during recording or nothing
records onto the tape.
• Correctly set the receiver/amplifier’s
controls.
• The receiver/amplifier or other audio
signal source is not delivering an
audio signal to the deck.
• Turn up REC LEVEL.
• The REC LEVEL control is set too
low.
• Check all connections.
• Clean the tape heads.
• There are connection problems.
• The tape heads are dirty.
The sound is unstable or
interrupted.
• Clean all tape handling parts.
• The heads, pinch rollers, capstans, or
other tape-handling parts are dirty.
• The tape is not uniformly wound.
• Completely rewind then fast forward the
tape.
High-frequency sounds are
missing.
• Correctly set DOLBY NR.
• A tape recorded without Dolby NR is
being played back with DOLBY NR
set to B or C.
• Clean the tape heads.
• The tape heads are dirty.
15
TROUBLE SHOOTING
Symptom
Cause
Remedy
High-frequency sounds are
emphasized.
• A tape recorded with Dolby NR is
being played back with DOLBY NR
set to OFF.
• Set DOLBY NR to the same position as
was used for recording.
The sounds from previous
recordings are still on the tape
with new recordings.
• The tape heads are dirty.
• Clean the tape heads.
The sound is distorted.
• The recording level is too high.
• The original signal was distorted.
• The heads are dirty.
• Turn down REC LEVEL and re-record.
• Replace the original recording source.
• Clean the tape heads.
There is too much noise.
• Poor-quality tape is being used.
• There is a faulty connection.
• Recording level is too low.
• The tape heads are dirty.
• Use a better-quality tape.
• Check all connections.
• Turn up REC LEVEL and re-record.
• Clean the tape heads.
ASMS does not operate properly. • Blanks between selections are less
than 4 seconds long.
• Use tapes with blanks of 4 seconds or
more between selections.
The system remote control does • The control cord is not connected.
not work.
• Properly connect the control cord.
CD-deck synchro recording
does not work.
• The CD-deck synchro control cord is • Properly connect the control cord.
not connected.
• The cassette tape’s erase protection
tabs are broken.
• Replace the cassette with one with
unbroken tabs or cover the holes with
tape.
The CD-DECK SYNCHRO
stops working during CD-Deck
Synchro recording.
• The end of the tape was reached
during CD-Deck Synchro recording.
• After the deck entered the standby
mode, more than 1 minute elapsed
before the CD player resumed play.
• Replace the tape with a longer one.
• Change the disc and press CD
SYNCHRO RECORD again.
16
SPECIFICATIONS
System ......................................................................................................................................... 4-Track, 2-Channel Stereo
Heads................................................................................................................ One Hard Permalloy Record/Playback Head
One Hard Permalloy Playback Head
One Ferrite Erasing Head
Motors ................................................................................................................................................ Two DC Servo Motors
Wow and Flutter .................................................................................................................................... 0.09% (WRMS, JIS)
Fast Winding Time ......................................................................................................... Less than 120 seconds (C-60 tape)
Frequency Response (at -20 dB recording level):
Type IV (Metal) Tape ............................................................................................................................. 20 to 16,500 Hz
Type II (Chrome) Tape ........................................................................................................................... 20 to 16,000 Hz
Type I (Normal) Tape............................................................................................................................. 20 to 16,000 Hz
Signal-to-Noise Ratio (Dolby NR Off) ......................................................................................................... More than 45 dB
Noise Reduction Effect:
Dolby B NR ON.................................................................................................................... More than 10 dB (at 5 kHz)
Dolby C NR ON ................................................................................................................... More than 19 dB (at 5 kHz)
Harmonic Distortion .......................................................................................... No more than 0.8% (at -4 dB: 160 nwb/m)
Input (Sensitivity) LINE (INPUT) .............................................................................. 100 mV (Input Impedance 68 kOhm)
Output (Reference level) LINE (OUTPUT) ................................................................. 0.5 V (Output Impedance 1.9 kOhm)
Power Requirements .................................................................................................................................... AC 120V, 60 Hz
Power Consumption ............................................................................................................................................... 17 Watts
Dimensions .................................................................................................................. 415/16 ✕ 169/16 ✕ 913/16 Inches (HWD)
.................................................................................................................................................... (125 ✕ 420 ✕ 250 mm)
Weight ..................................................................................................................................................... 9 lbs 1 oz (4.1 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.
17
INDEX TO FEATURES BY CONTROL NAME
This table lists the control and indicator names on the
front of your SCT-560 along with the page number where
the item is discussed.
Control
Page
3
2
6
6
ASMS 1 and ¡
CD SYNCHRO RECORD
DEMO
8
12
9
DOLBY NR
EJECT
7
6
HI-SPEED
NORMAL
PAUSE
11
11
8
POWER
6
REC LEVEL
REC MUTE
RECORD
10
11
10
8
RELAY/SKIP
RESET
8
REV MODE
REWIND AUTO PLAY
STAND BY
STOP
6,9
9
6
6
TIME/COUNTER
8
18
NOTES
19
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship
under normal use for one (1) year from the date of purchase from RadioShack company-owned stores
and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack
MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS
PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER
OR ANY OTHER PERSON OR ENTITY WITH RE-SPECT TO ANY LIABILITY, LOSS OR DAMAGE
CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES
RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT
OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. In the
event of a product defect during the warranty period, take the product and the RadioShack sales receipt
as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise
provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace
the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts
and products, and products on which a refund is made, become the property of RadioShack. New or
reconditioned parts and products may be used in the performance of warranty service. Repaired or
replaced parts and products are warranted for the remainder of the original warranty period. You will be
charged for repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other
than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or
batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product
removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
09/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
14-1403
<PRB1200-A>
Printed in XXXX
09A99
|