QSC Audio Speaker HPR M KIT 122 User Guide

1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA  
Main Number (714) 754-6175 or toll free (USA only) (800) 854-4079  
Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834  
HPR M10 KIT User Manual  
This suspension kit is required for vertical suspension of the QSC HPR122i from a solid structure or for the vertical suspension of the QSC HPR122i, HPR152i or  
HPR153i from a solid structure. For horizontal suspension of the HPR122i, the HPR SUS KIT 122 is required. Do not suspend the HPR152i or HPR153i enclosures  
horizontally.  
Contents:  
Eyebolt, M10, steel, 3 each  
• Spacer, aluminum, 2 each  
Conical spring washer, 2 each  
Important Safety Precautions & Explanation of Symbols  
Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer.  
WARNING! The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and mainte-  
nance (servicing) instructions in this manual.  
Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, enclosures,  
transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated com-  
ponent could significantly reduce the strength of the installation or placement. Any such condition severely reduces  
the safety of the installation and should be immediately corrected. Use only hardware which is rated for the loading  
conditions of the installation and any possible short-term, unexpected overloading. Never exceed the rating of the  
hardware or equipment.  
Consult a licensed, Professional Engineer regarding physical equipment installation. All local, state and national reg-  
ulations regarding the safety and operation of equipment are understood and adhered to.  
Use only load rated hardware to attach to the eyebolts or pull-back bar when suspending these products.  
Do not suspend these products from any structural element on the enclosure other than the load rated M10 suspension  
points.  
Do not suspend the HPR152i or HPR153i horizontally under any circumstances using this or any other hardware.  
Vertical Suspension of the HPR122i  
Install Two Top-surface Eyebolts  
On the top of the enclosure, near the front corners, are M10 flat-head screws which must be removed and  
have an eyebolts installed in their place.  
Eyebolt installation loca-  
tions for vertical suspension  
of the HPR122i loudspeaker.  
1- Remove the factory installed M10 flat-head screws from the top of the enclosure using a 6mm hex wrench.  
2- Thread an eyebolt into each of the enclosures threaded inserts; do not use flat washers or standoffs on the  
top eyebolts. Tighten eyebolts.  
Install One Pull-back Eyebolt  
At the rear of the enclosure, just below the amplifier module, is a M10 flat-head screw which must be  
removed and have an eyebolt installed in its place.  
1- Remove the factory installed M10 flat-head screw from the enclosure using a 6mm hex wrench.  
2- Thread an eyebolt into the enclosures threaded insert; do not use a standoff on the pull-back eyebolt.  
Tighten eyebolt.  
Do not use the eyebolt spacers when suspending the HPR122i loud-  
speaker vertically. They are for use on the HPR152i and HPR153i loud-  
speakers.  
Note! Be sure to tighten each eyebolt until shoulder is snug against the  
enclosure. Tighten the eyebolts down and then continue to rotate until  
they are positioned as desired.  
 

Radio Shack Baby Toy 60 2626 User Guide
Radio Shack Microphone 32 1230A User Guide
RCA Tablet RCT6203W46 User Guide
Roland Electronic Keyboard DP 990R User Guide
Roper Range 336 User Guide
Samson Stereo Equalizer S Equalizer User Guide
Samsung Car Video System 305TPLUS User Guide
Sanyo Flat Panel Television AVL 263 User Guide
Sceptre Technologies Flat Panel Television X505BV FHD User Guide
Senco Power Screwdriver DS205 14V User Guide